Professional self-adhesive label manufacturer providing customized production for food, pharmaceutical, logistics, industrial and other industries.
Self-Adhesive Labels · Source FactoryFrom Design to Labeling: Full-Service Support
National Hotline15861193257
Get a Quote
You are here: Home>News>Industry News

Making Room for the 2D Code on a Retail Pack

Date: 2026-11-11 Source: Xuzhou HuaiLion Views: 16
In short

Retail packs are moving toward 2D codes carrying batch and expiry data. Artwork space, quiet zones and the printing setup all need planning.

The barcode scanned at a checkout for decades carries one thing, a product identifier. Batch, expiry date and serial number live on a second small label or in the paperwork. The next generation of 2D codes puts all of that into one symbol, and GS1 calls the migration Sunrise 2027, an effort to get scanning equipment ready to read both linear and two-dimensional codes. For anyone specifying labels, the change lands on two concrete jobs, artwork and printing.

One symbol, far more data

These codes organise data in a web-like syntax. The product identifier forms the base, with batch, expiry and serial fields attached. A scanner at the till reads the identifier and completes the sale; a phone pointed at the same symbol can open an ingredients page, a traceability record or a recall notice. More fields mean more modules, so at the same physical size each module gets smaller and the demand on print resolution and contrast goes up. A linear code that prints cleanly at 203 dpi may need 300 dpi once the payload grows.

A shopper scanning the code on a food jar in front of a store shelf

Quiet zones again, but square

A 2D symbol needs clear space on all four sides. The narrow strip that held a linear barcode often cannot fit a square of the required size, which is a real constraint on small cosmetics, pens and pharmaceutical cartons. Designers also like putting a logo in the middle of the symbol. That works only while enough error correction remains, and an oversized mark costs read reliability at the till.

Replanning the label and its position

Three transition layouts are common. Keep both codes side by side until downstream readers are replaced. Put the 2D symbol on the back or side of the pack and leave the front alone. Or enlarge the main label and rebuild the artwork. The choice depends on available area, whether the applicator can reach that surface, and where readers sit, on the shelf or at the checkout.

Curved and reflective surfaces

On a curved bottle or a flexible pouch, the symbol can be stretched or land on a wrinkle, deforming modules and cutting read rates. A stiffer film face stock behaves better than thin paper, and application has to control bubbles and folds. Metallised film and metal cans reflect strongly, so modules blur together. A white patch underneath or a suitable overlaminate usually fixes it, followed by a read test at the actual scanning angle.

What changes on the printing line

Batch and expiry fields change with every run, so this is variable data. Laser marking, thermal transfer and inkjet are the usual routes. Thermal transfer gives crisp edges and stable grades, with speed limited by label length. Inkjet is fast but its dot edges are rougher, which small modules tolerate poorly. Whichever route is chosen, put an inline verification read on the line and reject or reapply anything that fails. A wrong code that reads correctly is far more expensive downstream than one that is rejected at the printer.

Grading standards change too. Linear symbols are graded under ISO/IEC 15416, while 2D symbols use ISO/IEC 15415. The parameter sets differ, so an existing verifier and its worksheet do not carry over unchanged. Update the acceptance clause when the symbol changes, or supplier and customer will arrive with two incompatible reports.

Live with both for a while

Checkout systems and store equipment are replaced on different schedules, so both symbols will coexist for some time. Leave room for two codes, or design artwork that switches easily. At HuaiLion, a new layout for food or personal care packs starts with a position drawing based on the real pack dimensions, followed by applied samples tested from both the shelf side and the till side before the plate is released.

Settle the data fields early

Decide how many digits the batch uses, the expiry format and which system supplies the serial number while the artwork is still open. Then a later printer swap does not force a rebuild of the label and the database together. The symbol is only the output; the field definitions are the part worth getting right first.

WeChat QR code

Scan to chat on WeChat